donaldmoney0

Reasons Your Fiat 500 Key Fob Won't Work A key fob for the Fiat 500 is a convenient way to unlock the doors and get started the car. There are many reasons why the fob may stop working. This could be due to a dead coin-battery, water damage, problems with receiver modules, as well as interference. This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons. Dead Coin Battery A dead battery is probably the most common reason for your 500 key fob being inoperative. Modern key fobs offer only a limited range of operation and must be within just a few inches of the vehicle in order to function. If you are far from your vehicle and press the key fob button the car will not respond, and will display an “Key Fob Not Detected” message in the instrument cluster. If this happens, replace the battery on your coin cell (Part number CR2032) with a new one from a reliable brand such as Panasonic, Duracell, or Energizer. They can be found in the local hardware store or on the internet. After you've replaced the coin cell battery You can test it by standing next to your Fiat 500 and pressing the buttons. The car will flash its parking lights, and the key fob should be able to operate the lock and unlock switches. If the key fob won't function after replacing the battery, it might be damaged by water that blocks it from connecting to the receiver module inside your car. Water damage can happen in a variety of ways, such as the simple splash or submerging your key fob in saltwater at the beach. If you believe your fob was exposed to water, place it in a rice bag to draw out the moisture. If this does not work, you'll need to have your fob reprogrammed either by an auto locksmith or a dealer. Water Damage While the fob has some rubber seals that keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and then fail. It's not the best idea to submerge the fob in water however, but don't give it up if you accidentally drop it in water or fail to remove it from your pants pocket. First, remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Check the fob again to verify if it's working. If the fob doesn't work, it might need to be changed. This is usually handled by an auto locksmith or dealer. If your key is a bit older and has not been programmed for your car, you will need to replace it completely. This is a simple process that can be handled by a professional automotive locksmith. The locksmith will require the key to be cut to match the car's ignition. The locksmith also needs to reprogram your fob in the car's system. This is a simple and affordable process which can be completed in the same day. Receiver Module Issues One of the most common reasons why your 500 key fob won't be working is that it's simply out of range. The remote has a maximum range of 30 feet, which means in the event that you are far away from your vehicle it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it starts responding. If your fob does not work after you replace the coin battery, also called a “button”, “watch” or “button” It could be a problem with the internal circuit board. Reprogramming the fob is usually the solution to this problem. There are instructions on how to do this for the majority of automobiles by searching YouTube or reading the owner's manual. It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, it could prevent the battery from sitting properly, and this will cause the remote to malfunction. In rare cases the fob could be out of connection with your vehicle as a result of hardware or software problems. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, the software may also need to be reinstalled in your body control modules. Interference In addition to a dead battery on a coin the key fob could not be able to transmit or receive an signal due to interference. This could occur if the key fob is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons why the key fob may not function could be due to a weak connection to the buttons and internal chip or water damage. If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. It could be a defective 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module, located beneath the dashboard, picks up radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets. Luckily, there is an easy method to reset all on-board systems in your 500 and include the key fob. Disconnect fiat 500 replacement key for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer in your car. This will help you get your key fob to function again. If the problem persists you should speak with an expert technician. They will be able to determine the root cause of any problems.